![]() This is only very bad, it is a serious dysfunctionality, and for sure you will get the same feedback from many other users.Īs I can see too in the last version, there is not possible anymore to move an entire trace at once, nor step by step, nor with the mouse, nor by selecting it the whole, or many segments at once. The arrow keys it work for all of the objects in DipTrace (as it should, and as normal) except the traces (in latest version). This step by step movement, using keyboard (arrow keys) is a basic function in any CAD software, and for sure you all there know about such basics. The problem here is that any and every alternative to such operation is only much more complicated, and more time consuming than the simple pressing of a few keys on keyboard, for the steps one may need in moving/positioning process. ![]() There are some alternatives to move traces around. Then I got few suggestion for alternative methods to move and position traces in 3.0 version. It is very difficult to return it therefore we haven't done it." We fixed the bug and moving traces by arrow key is not working anymore. "Moving traces using arrow keys was accidental side effect of a bug in the software. As the traces are connected to anything else, then are not possible to be moved by keys, but only with the mouse pointer.Īs such basic functionality it is very important, I expect to be prioritised in the bug elimination process, and finally reestablished.ĭipTrace support team answer to my above bug report: I noticed this time that the traces are movable using the arrows keys only if are alone and not connected to any other objects (pads, vias, etc). This it was the normal (and very useful) functionality for the all old versions. As I can see, it still not be addressed the quite important issue/bug which is particular only to the last version, as I reported previously: the traces are not longer movable by arrows keys (in small/precise steps). DIPTRACE FORUM UPDATEPublison- if you figure it out, lemme know! I'll be sure to post any tidbits I figure out.I installed the new build update for 3.0 DipTrace version. Rick sand Dave- thanks! I'mma keep trying. But the other great advantage is being able to "tap" power or ground from anywhere on the board, wherever you need it-without using real estate for the trace to get it there. The biggest advantage to having separate power and ground planes is minimized routing on the top and bottom signal planes. I wish I had more time to learn it, but for now I'm somewhat limited (hence my question.) DIPTRACE FORUM SOFTWAREDiptrace, so far seems like it's a much better software package and incredibly useful. I've only created pcb with ExpressPCB which is incredibly simple to use, and creating the power and ground planes is very straight forward. Thanks! I'd like to keep a segregated power and ground plane for managing stray capacitance and noise and such, as Dave Hein and Duane D have pointed out. ![]() Is that what you really need?ġ - Make first attempt to define board sizeĢ - Work the component placement according to schematic/connector needsĤ - If after "N" attempts (depending on schematic compplexity and max board size requirements) I don't succeed then try 1 layer + jumpers on second layer.ĥ - If not possible revert to 2 layer designĪlex- Very good points, and that's a good strategy. Second, even if you could do 4 layers, are you sure you want that? It's more expensive and you will not be able to do a DIY board. DIPTRACE FORUM FREEHowever- it routes traces for Vcc and Gnd to each component on the signal layers.Ĭan someone explain what I need to do to make the Vcc and Gnd connections connect directly to a 3rd and 4th plane (Vcc and Gnd?) This should eliminate the traces.įirst the free version is " All features and libraries, 300 pins and 2 signal layers, non-profit use only" The schematic has no errors, and when I use it to create a PCB it lays everything out fine. My attachment is the schematic that I'd like to turn into a board with 2 signal layers, a ground plane and a power plane (3.3v) I'm just getting started using DipTrace and I am trying to figure out what I'm doing wrong here. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |